copy
Operating side of left and right; maximum copy length 320 mm for insertion into the lower part of the hand pad Shaft diameter 30 mm Scanner for sharpening steel and bell knife 1 steel holder 12x12 mm with carbide turnip HW08 1 bell knife Ø 14 mm with cranked holder adjustable plexiglass protection; 1 stencil blank 75 x 4 x 330mm Stencil feed on both sides; hexagon key 13/17mm Operating instructions (Build-up height from hand rest to center of tip approx. 49 mm)
The copier LP320-F is an additional device for copying and facing. It is inserted into the handrest base. Thus, it can be mounted in seconds. The scanning is done via a dual push-button for round and pointed steel. A double-sided fine feed facilitates setting and also serves as an notification the workpiece diameter. The handwheel can be mounted on both sides. The longitudinal and transverse movement runs on play-free guides. operating side on both sides copy length 320 mm - profile depth 62 mm height adjustment ring dual push-button for round and pointed steel 1 HM insert HW08 with steel holder 1 bell-shaped steel holder cranked 12 x 12 mm 1 bell knife Ø 14 mm adjustable plexiglass protection 1 stencil blank 75 x 4 x 330 mm weight approx. 10.5 kg (steel holder 12 x 12 mm)
The copier LP320-F is an additional device for copying and facing. It is inserted into the handrest base. Thus, it can be mounted in seconds. The scanning is done via a dual push-button for round and pointed steel. A double-sided fine feed facilitates setting and also serves as an notification the workpiece diameter. The handwheel can be mounted on both sides. The longitudinal and transverse movement runs on play-free guides. operating side on both sides copy length 320 mm - profile depth 62 mm height adjustment ring dual push-button for round and pointed steel 1 HM insert HW08 with steel holder 1 bell-shaped steel holder cranked 12 x 12 mm 1 bell knife Ø 14 mm adjustable plexiglass protection 1 stencil blank 75 x 4 x 330 mm weight approx. 10.5 kg (steel holder 12 x 12 mm)
only substructure - without copy unit; can be retrofitted for copier LP320-F during longitudinal turning, exact adjustment to 90 ° to the bed is possible via bracket when facing without loss of height via turning over the device - with 2 bolts for longitudinal and transverse construction - substructure over 2 shafts Ø 30 mm height adjustable - steel plate 350x300x10 mm with 2 tubes and fixing screws - 2 height adjustment holes 30 mm - base plate 50x10x330 mm with 2 screwed-on shafts - 2 clamping plates with threaded rods - PVC spacers for Hager models important: make / type with top height! weight substructure approx. 9.5 kg from top height 130 mm can be built up
only substructure - without copy unit; can be retrofitted for copier LP320-F during longitudinal turning, exact adjustment to 90 ° to the bed is possible via bracket when facing without loss of height via turning over the device - with 2 bolts for longitudinal and transverse construction - substructure over 2 shafts Ø 30 mm height adjustable - steel plate 350x300x10 mm with 2 tubes and fixing screws - 2 height adjustment holes 30 mm - base plate 50x10x330 mm with 2 screwed-on shafts - 2 clamping plates with threaded rods - PVC spacers for Hager models important: make / type with top height! weight substructure approx. 9.5 kg from top height 130 mm can be built up
The copier LP520-F is an additional device for copying and facing. copy length 520 mm - profile depth 62 mm height adjustment ring dual push-button for round and pointed steel 1 HM insert HW08 with steel holder 1 bell-shaped steel holder cranked 12 x 12 mm 1 bell knife Ø 14 mm adjustable plexiglass protection 1 stencil blank 75 x 4 x 520 mm weight approx. 21 kg (steel holder 12 x 12 mm)
The copier LP520-F is an additional device for copying and facing. copy length 520 mm - profile depth 62 mm height adjustment ring dual push-button for round and pointed steel 1 HM insert HW08 with steel holder 1 bell-shaped steel holder cranked 12 x 12 mm 1 bell knife Ø 14 mm adjustable plexiglass protection 1 stencil blank 75 x 4 x 520 mm weight approx. 21 kg (steel holder 12 x 12 mm)
largest scannable original part Ø 100 mm 2 basic frame can be tightened and tightened via screws (for easy clamping in template holder) largest original clamping diameter approx. 100 mm 1 extended scanner tip 1 extended scanner-round with movable roller
copy length 1040 mm - profile depth 110 mm 2 end stops double pushbutton for round and pointed steel 1 bell knife HSS Ø 20 mm 1 bell-shaped steel holder cranked 1 HM insert HW08 with steel holder adjustable plexiglass protection 1 stencil blank 85 x 4 x 1000 mm (steel holder 12 x 12 mm) weight about 42 kg length-depth-height: 1200-760-410 mm (minimum motor power lathe 1,1 kW)
copy length 1040 mm - profile depth 110 mm 2 end stops double pushbutton for round and pointed steel 1 bell knife HSS Ø 20 mm 1 bell-shaped steel holder cranked 1 HM insert HW08 with steel holder adjustable plexiglass protection 1 stencil blank 85 x 4 x 1000 mm (steel holder 12 x 12 mm) weight about 42 kg length-depth-height: 1200-760-410 mm (minimum motor power lathe 1,1 kW)
simple conversion and matured technology also when copying from the original part 7 pieces with instructions
9-teiliglanger Taster rund mitdrehend - langer Taster spitz2 verstellbare Arme für Originalwerkstück mit Gewindeverstellung2 Abstützböcke für dünnes OriginalwerkstückHandradverlängerung mit KontermutterU-Schienenabstützung für lange Taster
